Philips Cable Box SWW1810 User Manual

www.philips.com/welcome

SWW1810

EN User manual

Contents

Important

Safety

Y o u r W ireless HD AV Connect

Connect the transmitter to your HD devices

Connect the receiver to the HDTV set

Connect the IR blaster and IR sensor

extender cables

Install remote control batteries

Activate you r W ireless HD AV

Connect and set up the link

T u rn on the power of your HDTV

Activate the wireless link

Mount your receiver

Mount your receiver on the wall

Mount your receiver on the back of the

HDTV

T e chnical data

Supported resolution

Product speciﬁcations

Disposal of your old product and batteries

On e Y e ar Limited Warranty

Frequently asked question

e Do not use this apparatus near water.

1 Important

f Clean only with dry cloth.

g Do not block any ventilation openings.

Install in accordance with the

Safety

manufacturer’s instructions.

h Do not install near any heat sources such

as radiators, heat registers, stoves, or

other apparatus (including ampliﬁers) that

produce heat.

i Do not defeat the safety purpose of

the polarized or grounding-type plug.A

polarized plug has two blades with one

wider than the other.A grounding type

plug has two blades and a third grounding

prong.The wide blade or the third prong

are provided for your safety. If the provided

plug does not ﬁt into your outlet, consult

an electrician for replacement of the

obsolete outlet.

This ‘bolt of lightning’ indicates uninsulated

material within your unit may cause an electrical

shock.

The ‘exclamation mark’ calls attention to

features for which you should read the enclosed

literature closely to prevent operating and

maintenance problems.

Warning

• To reduce the risk of ﬁre or electric shock, this

apparatus should not be exposed to rain or moisture

and objects ﬁlled with liquids, such as vases, should not

be placed on this apparatus.

j Protect the power cord from being

walked on or pinched, particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

Caution

k Only use attachments/accessories speciﬁed

by the manufacturer..

• To prevent electric shock, fully insert the plug. (For

regions with polarized plugs:To prevent electric shock,

match wide blade to wide slot.)

l Use only with the cart, stand, tripod,

bracket, or table speciﬁed by the

manufacturer or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

Important Safety Instructions

a Read these instructions.

b Keep these instructions.

c Heed all warnings.

m Unplug this apparatus during lightning

storms or when unused for long periods of

time.

d Follow all instructions.

n Refer all servicing to qualiﬁed service

personnel. Servicing is required when

the apparatus has been damaged in any

way, such as power-supply cord or plug

is damaged, liquid has been spilled or

objects have fallen into the apparatus, the

apparatus has been exposed to rain or

moisture, does not operate normally, or

has been dropped.

o Battery usage CAUTION –To prevent

battery leakage which may result in bodily

injury, property damage, or damage to the

unit:

•

Do not mix batteries (old and new or

carbon and alkaline, etc.).

•

Remove batteries when the unit is not

used for a long time.

p Apparatus shall not be exposed to

dripping or splashing.

q Do not place any sources of danger on the

apparatus (e.g. liquid ﬁlled objects, lighted

candles).

Warning

• Use only the provided power adapter.

2 YourWireless

HD AV Connect

HDMI cable

Congratulations on your purchase and welcome

to Philips!

To fully beneﬁt from the support that Philips

offers, register your product at www.philips.

com/welcome.

IR blaster extender cable

What is in the box

Note

• Make sure you have all these items in the box. Contact

your dealer for any missing or damaged items.

Power adapter for the transmitter and receiver

x 2

IR sensor extender cable

Transmitter

Anchors x 2

Screws x 2

Quick Installation Guide

Adhesive tape x 2

Quick start guide

Receiver

User manual

Remote control

3 Overview

The receiver

Top view

The transmitter

Front view

Source LEDs Indicators for HDMI1

and HDMI2

Power

Press to turn the receiver

Source LEDs It displays the current

source input.

button with on/off.

the LED

indicator

SOURCE

Press to switch the

source input of the

transmitter.

button

Source

button

Press to select the

source input.

Power button Press to turn the

with the LED transmitter on/off

indicator

Rear view

DC IN

jack

HDMI

OUT

adapter

Connect the power adapter

of the receiver.

Connect the HDTV with an

HDMI cable.

POW

DC IN jack Connect the power

adapter of the transmitter.

2 & 3 HDMI IN Connect the HD audio/

IR IN jack Plug in the IR sensor

extender cable.

adapters

video device with the

HDMI cables.

IR OUT

blaster

extender

jack

Plug in the IR blaster

extender cable.

The remote control

POWER Press to turn the

button

transmitter and receiver

on/off.

INFO

button

Displays on the HDTV

the connection status of

the receiver.

button

Press to switch the IR

blaster frequency to meet

the requirement of the

source device.

SOURCE Press to switch the

button

audio/video source

inputs connected to the

transmitter.

The Wireless HD AV Connect gives you a total

wireless solution to place your HDTV set or

projector anywhere you want.The transmitter

can transmit uncompressed video content

over 65 feet (19.7 meters) without latency.The

receiver can receive signals for viewing on your

HDTV.All you need to do is to:

•

Connect the transmitter to your HD

devices. Examples of HD devices are cable/

satellite box, Blu-Ray/HD DVD player, game

console or computer.

Note

• These devices must have an HDMI port..

•

Connect the receiver to your HDTV set.

Control the transmitter with the remote

control.

2 Connect the supplied power adapter to

4 Installation

the transmitter.

•

Connect one end of the power

adapter to the DC IN jack of the

transmitter.

Connect the transmitter to

your HD devices

•

Connect the other end of the power

adapter to a power outlet.

The power button of the transmitter

is lit in solid blue and turns red in

standby mode.

You can connect two audio/video sources to

the transmitter at the same time, but only one

source can be selected and played.

Connect the receiver to the

HDTV set

HDMI OUT

IR IN

DC 5V

1 Connect the audio/video source to the

HDMI IN

transmitter using the supplied HDMI cable.

•

Connect one end of the HDMI cable

to the HDMI IN connector of the

transmitter.

1 Connect the receiver with an additional

HDMI cable (not supplied):

•

Connect one end of the HDMI cable

to the receiver.

Note

•

Connect the other end to the HDMI

IN connector of your HDTV.

• There are two HDMI IN ports but only one HDMI

cable is supplied.To connect two audio/video sources

to the transmitter at the same time, you need an

additional HDMI cable.

2 Connect the supplied power adapter to

the receiver:

•

Connect one end of the power

adapter to the DC IN jack of the

receiver.

Connect the other end of the power

adapter to a power outlet.

The power button of the receiver is lit

in solid blue and turns red in standby

mode.

•

Connect the other end of the HDMI

cable to the HDMI OUT connector of

the video source.

•

5 Extend and stick the IR sensor extender

Connect the IR blaster and IR

sensor extender cables

cable onto the front side of your HDTV.

Note

Tip

• The IR blaster support 47KHz remote signal protocol,

while the IR sensor supports 36KHz - 56KHz (NEC,

RC5, RC6) remote signal protocol.

• If you cannot use the remote control of your device,

follow the steps in this section to connect the sensor

extender cables .

Install remote control

batteries

Caution

• Risk of explosion! Keep batteries away from heat,

sunshine or ﬁre. Never discard batteries in ﬁre.

• Risk of decreased battery life! Never mix different

brands or types of batteries.

• Risk of product damage! When the remote control is

not used for long periods, remove the batteries.

Connect the infrared blaster or sensor extender

cables if necessary.

1 Plug the IR blaster extender cable into

the IR OUT blaster extender jack of the

transmitter.

1 Open the battery compartment.

2 Extend and stick the IR blaster extender

cable onto the front panel of the HD

device.

2 Insert two AAA batteries with correct

polarity (+/-) as indicated.

3 Close the battery compartment.

3 After the IR blaster extender cable is

connected to the transmitter, you can

control your HD device with the remote

control. Make sure that the remote control

points to the receiver.

4 If the distance between the receiver and

receiver has obstruction (e.g. the receiver

is mounted at the back of the HDTV), plug

the IR sensor extender cable into the IR

IN jack of the receiver.

10 EN

On screen display on HDTV

5 Activate your

Wireless HD AV

Connect and set

up the link

On screen Mode and status

display

Standby mode: it is a power-

saving mode

.....

Start up in progress: It takes 15-

20 seconds.

x and .... Searching available channels: It

occurs when the link cannot

establish over 80 seconds after

initialization.

Turn on the power of your

HDTV

HDMI On mode with unrecognized

HDMI OUT

IR IN

CH1

video format

DC 5V

HDMI On mode but without input

HDM

CH1

from the source device

HDMI On mode with recognized video

CH1 1080P format

I H D

1 Go to the source menu under the settings

menu of your HDTV.

2 Select the HDMI input to which the

receiver is connected.

EN 11

Select the source on the transmitter

Activate the wireless link

Press the source buttons on the remote

control, transmitter or receiver until you see the

available video from your device.

Switch on the transmitter and receiver

In standby mode, a red power LED displays on

the transmitter and receiver.You can then turn on

the transmitter and receiver in the following ways:

Tip

• For information on the LED indicator status, see the

section on ‘LED indicator status of the transmitter’.

LED indicator status of the

transmitter and receiver

Power Source Mode and status

LED

Solid

red

LED

Off

Standby mode: it is a

power-saving mode

•

Press on the remote control.

» Both the transmitter and receiver are

turned on.

Flashing Flashing Start up in progress: It takes

blue blue 15-20 seconds.

Flashing Flashing Searching available channels:

blue

It occurs when the link

cannot establish over 80

seconds after initialization.

Flashing On mode but without

quickly input from the source

device

Solid

blue

Solid

blue

Solid

blue

Flashing On mode with

slowly unrecognized video format

Solid

blue

On mode with recognized

video format

•

Press on the transmitter and receiver.

Note

• If the link is not established after 80 seconds, move the

transmitter, receiver and HDTV closer to each other.

The maximum transmission range is up to 65 feet (19.7

meters).

• If more than one set of Philips Wireless HD AV Connect

is placed in the same room, make sure that the minimum

distance among each one is 6 feet 6 inches (2 meters).

• If using a computer, make sure the video format is

supported before the video is displayed, see the

chapter on ‘Technical data’ for information.

Establish the link between the

transmitter and receiver

A ﬂashing blue power LED displays until

the signal link between the two units are

established. Normally, it takes around 15-20

seconds for the link to establish successfully.

• If using a computer, and the picture on yourTV is

not full screen, see the chapter on ‘Frequently asked

questions’ for information.

12 EN

5 Hook the key holes at the back of the

6 Mount your

receiver

receiver on the screws.

You can either mount the receiver on the wall

or on the back of the HDTV.

Mount your receiver on the

wall

1 ^{Select a spot near the HDTV.}

2 Drill two holes in the wall. Make sure that

the distance between the two holes is

1 ²⁵/32” (45 mm) and the diameter of the

hole is ³/16” (5 mm).

3 Punch the supplied two anchors into the

two holes on the wall.

4 Put the two screws into the anchors and

leave ¹/8” (3 mm) to mount the receiver on.

EN 13

6 Align the adhesive tape on the receiver

with the one on the HDTV until both the

receiver and HDTV are mounted together

ﬁrmly.

Mount your receiver on the

back of the HDTV

1 ^{Remove the white protective ﬁlm from}

one of the supplied adhesive tapes.

Note

2 Secure the glued side of the adhesive tape

and attach it to the central bottom area of

the receiver.

• The use of adhesive tapes is an alternative mounting

option when the receiver cannot be ﬁxed.

• When you mount the receiver at the back of the

HDTV, avoid blocking the ventilation holes of the

HDTV.

• For safety reason, check regularly if the HDTV and

receiver are mounted together ﬁrmly.

• The receiver is not recommended for in-the-wall

installation.

3 Select a ﬂat location on the rear side of

the HDTV.

4 Remove the white protective ﬁlm from the

other adhesive tape.

5 Secure the glued side of the adhesive tape

and attach it to the selected rear side of

the HDTV.

14 EN

Power supply:

7 Technical data

Input:AC 100~ 240V

Output: DC 5V, 2A

Operating temperature:

0~40°C/32~104°F

Supported resolution

Video format

timings

Resolution

Transmitter interfaces

Primary CEA

video timing

480p

576p

720p

1080i

A/V interfaces

HDMI input:Two (Type A)

Control signal interfaces

IR blaster extender: 2.5mm jack

Power interface

Power input: 5V DC jack

Switches

Top power switch: One

Top source switch: One

LEDs

Power LED: 1 x blue/red LED

Source LED: 2 x blue LED

Dimensions

640x480p @ 59.94/60Hz

720x480p @ 59.94Hz

720x480p @ 60Hz

720x576p @ 50Hz

1280x720p @ 50Hz

1280x720p @ 59.94/60Hz

1920x1080i @ 50Hz

1920x1080i @ 59.94/60Hz

1920x1080p @ 50Hz

1920x1080p @ 59.94/60Hz

1080i

1080p/60

194.8 x 146.8 x 31 mm (W x L x H)

Secondary CEA

video timing

1080p/24

Receiver interfaces

1920x1080p @ 23.98/24Hz

1920x1080p @ 25Hz

1920x1080p @ 29.97/30Hz

A/V interfaces

HDMI output: One (Type A)

Control signal interfaces

IR sensor: available

Power interface

Power input: 5V DC jack

Switches

Product speciﬁcations

Top power switch: One

Top source switch: One

LEDs

General speciﬁcation

Video resolution

Power LED: 1 x blue/red LED

Source LED: 2 x blue LED

Signal quality status: On-screen display

Dimensions

HDMI input: 1080p, 1080i, 720p, 576p, 480p

Supported audio formats:

Digital audio: up to 6 Mbps AC3 and DTS

Analog audio: 32-96 KHz and 16-24 bits per

audio sample

194.8 x 146.8 x 31 mm (W x L x H)

Transmission distance:

Maximum 65 feet (19.7 meters)

Antennas:

High performance internal antennas

Operating frequencies:

5.15-5.25/5.725-5.825 GHz

EN 15

IMPORTANT NOTE:

Radiation Exposure Statement:

8 Notice

•

This equipment complies with FCC

radiation exposure limits set forth for an

uncontrolled environment.This equipment

should be installed and operated with

minimum distance 20cm between the

radiator & your body.

Notice for USA

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation.This equipment generates,

uses and can radiate radio frequency energy

and, if not installed and used in accordance with

the instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference

by one of the following measures:

•

This transmitter must not be co-located

or operating in conjunction with any other

antenna or transmitter.

Note

• The country code selection is for non-US model only

and is not available to all US model. Per FCC regulation,

all wireless product marketed in US must ﬁxed to US

operation channels only.

Notice for Canada

This device complies with RSS-210 of the

Industry Canada Rules. Operation is subject to

the following two conditions: (1)This device

may not cause harmful interference, and (2) this

device must accept any interference received,

including interference that may cause undesired

operation.

•

Reorient or relocate the receiving antenna.

Increase the separation between the

equipment and receiver.

Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

•

Consult the dealer or an experienced

radio/TV technician for help.

IMPORTANT NOTE:

Radiation Exposure Statement:

FCC Caution:Any changes or modiﬁcations not

expressly approved by the party responsible for

compliance could void the user’s authority to

operate this equipment.

This equipment complies with IC radiation

exposure limits set forth for an uncontrolled

environment.This equipment should be installed

and operated with minimum distance 20cm

between the radiator & your body.

•

Operations in the 5.15-5.25GHz / 5.725-

5.825GHz band are restricted to indoor

usage only.

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions: (1)This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired

operation.

Caution

• The device for operation in the band 5150-5250 MHz is

only for indoor use to reduce the potential for harmful

interference to co-channel mobile satellite systems;

• the maximum antenna gain permitted for devices in the

band 5725-5825 MHz shall comply with the e.i.r.p. limits

speciﬁed for point-to-point and non point-to-point

operation as appropriate.

16 EN

negative consequences on the environment and

human health.

Please visit www.recycle.philips.com for

additional information on a recycling center in

your area.

Recycling

Your product is designed and manufactured

with high quality materials and components,

which can be recycled and reused.

Never dispose of your product with other

household waste. Please inform yourself about

the local rules on the separate collection of

electrical and electronic products.The correct

disposal of your old product helps prevent

potentially negative consequences on the

environment and human health.

HDMI, and HDMI logo, and High-Deﬁnition

Multimedia Interface are trademarks or

registered trademarks of HDMI licensing LLC in

the United States and other countries.

OneYear LimitedWarranty

The packaging of this product is intended to

be recycled. Contact your local authorities for

information about how to recycle the packaging.

Philips warrants that this product shall be free

from defects in material, workmanship and

assembly, under normal use, in accordance with

the speciﬁcations and warnings, for a period

of one year from the date of purchase.This

warranty extends only to the original purchaser

of the product, and is not transferable.To

exercise your rights under this warranty, you

must provide proof of purchase in the form of

an original sales receipt that shows the product

name and the date of purchase. For customer

support or to obtain warranty service, please

visit our website www.philips.com/support,

or dial in 1-888-744-5477.THERE ARE NO

OTHER EXPRESS OR IMPLIED WARRANTIES.

Philips’ liability is limited to repair or, at its

sole option, replacement of the product.

Incidental, special and consequential damages

are disclaimed where permitted by law.This

warranty gives you speciﬁc legal rights.You may

also have other rights that vary from state to

state.

When this logo is attached to a product, it

means a ﬁnancial contribution has been paid to

the associated national recovery and recycling

system.

Disposal of your old product

and batteries

Your product is designed and manufactured

with high quality materials and components,

which can be recycled and reused.

Never dispose of your product with other

household waste. Please inform yourself about

the local rules on the separate collection of

electrical and electronic products and batteries.

The correct disposal of these products helps

prevent potentially negative consequences on

the environment and human health.

Your product contains batteries, which cannot

be disposed of with normal household waste.

Please inform yourself about the local rules on

separate collection of batteries.The correct

disposal of batteries helps prevent potentially

EN 17

9 Frequently asked question

The power LED on the

receiver is not lit up in red in

standby mode.

•

Make sure that there is power supply for the transmitter and

receiver.

^{The computer screen image is}1 Right-click on an open space on your desktop.

not full screen on myTV.

2 Select Graphics Options > Output to > DigitalTelevision (Now

the laptop image will only appear on yourTV).

3 Once again, right-click on an open space on your desktop.

4 Select Screen Resolution.

5 On the pop-up box increase the resolution settings till the laptop

image better ﬁts yourTV screen.

6 Select OK and KEEP CHANGES when you are satisﬁed with

your image size..

There is no video displayed on •

myTV screen.

Make sure that the appropriate cables are selected and inserted

to the transmitter, receiver, and HDTV.

•

Make sure that you select HDMI as the input source on your

HDTV.

•

Check the power LED and SOURCE LED on the receiver:

•

Flashing blue power LED: Make sure that the transmission

range between receiver and transmitter is not over 65 feet

(19.7 meters) transmission distance. Move the transmitter

closer to the receiver.

•

Solid blue power LED + slow and ﬂashing source LED:1)

Make sure that the frame rate and video resolution of your

source device equipment are supported and conformed to

the technical speciﬁcation. 2) Connect the source device to

yourTV with an HDMI cable to check the compatibility of

the video format. 3) Make sure that the video solution your

source device is supported (See the chapter ‘Technical data’).

Solid blue power LED + quick and ﬂashing source LED: 1)

Make sure that the proper cables are connected among the

transmitter, receiver and HDTV. 2) Make sure that the source

devices connected to the transmitter are powered on.

•

18 EN

If the picture quality is poor,

what do I do?

•

Make sure that the video resolution of your source device

matches the resolution of your HDTV.

Make sure that the transmission range between receiver and

transmitter is not over 65 feet (19.7 meters) transmission

distance.

Tip

• For information, see the chapter on ‘Technical data’.

I cannot hear any sound or the •

Make sure that theTV volume is adjusted correctly.

Make sure that theTV volume is not set to minimum or the

sound is not muted.

sound is poor, what do I do?

•

Make sure that the audio format is supported.

Make sure the HDMI cable of the transmitter is connected

correctly.

Tip

• For information, see the chapter on ‘Technical data, section ‘Product speciﬁcation’.

I cannot control the source

device with the IR blaster.

•

Make sure that the IR blaster and IR sensor extender cables are

facing the IR lens of the HD device.

Press the IR button on the remote control to change the IR

blaster frequency based on the requirement of the source device.

Tip

• For information, see the chapter ‘Installation’, section ‘Connect to IR blaster and IR

sensor extender cables’.

EN 19

20 EN

IFU_SWW1810_EN_V2.0

WK11485

Pelco Car Video System PMCL317A User Manual
Philips Car Stereo System AQ4140 User Manual
Philips Car Stereo System CED780 User Manual
Philips Flat Panel Television PT418APT A User Manual
Philips Home Theater System DC310V User Manual
Philips Projection Television 7P5441C199 User Manual
Philips Stereo Amplifier BGD814 User Manual
Plantronics Headphones CS60 DECT User Manual
Polaroid Digital Camera IS326 RED User Manual
Polaroid Digital Camera PIC 300B User Manual