TM
PELICAN
LAMP REPLACEMENT
BATTERY INSTALLATION
1. Remove lens housing by turning counter-
clockwise.
1. Remove lens housing by turning counter-clockwise.
2. Remove the lamp and contact module.
3. Replace the contact module and lamp.
4. Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing
slightly.
TM
2. Remove the lamp and contact module.
3. Remove used batteries and replace with fresh
batteries as shown on the outside of the
engraved body.
4. Replace the contact module and lamp.
5. Replace lens housing squarely on threads and
turn clockwise while pressing on the lens hous-
ing slightly.
StealthLite 2400
23215 Early Ave. • Torrance, CA 90505 USA
Tel (310) 326-4700 • FAX (310) 326-3311
Cat. #2400
TM
PELICAN CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel (780) 481-6076 • FAX (780) 481-9586
PRODUCT SPECIFICATIONS
Lamp Type:
Battery Type:
Battery Brand:
Xenon
4 AA Cell Alkaline (Included)
Eveready® Energizer®
TM
PELI PRODUCTS, S.L.U.
ON/OFF
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Tel (+34) 93.467.4999 • FAX (+34) 93.487.7393
REPLACEMENT PARTS
Swing the switch lever to the right (light facing away
from you) until light activates. To turn light off, swing
the switch lever to the left (light facing away from
you) until light goes off.
SUBMERSIBLE
CAT #
2401
2404
DESCRIPTION
O-RING
LAMP MODULE
© PELICAN PRODUCTS 2010
2403-311-001 5-0697 Rev A AU/10
All trademarks and logos displayed herein are registered and unregistered
trademarks of Pelican Products, Inc. and others.
CAUTION: Read This Notice Before Use.
Hydrogen Gas Absorber Pellets
WARNING – Explosion Hazard - Batteries must
only be changed in non-hazardous locations
Eveready and Energizer are registered trademarks of Eveready Battery Company, Inc.
Located inside the flashlight are catalyst pellets which
are present to absorb hydrogen gas that could possibly
be emitted by defective, leaking, reversed polarity or
heavily discharged batteries. If the pellets become wet,
let them air dry. Pelican Products assumes no liability
for any brand batteries which are defective or cause
injury to anyone when used in any Pelican flashlight.
23215 Early Ave. • Torrance, CA 90505 USA
Tel (310) 326-4700 • FAX (310) 326-3311
WARNING –
Explosion Hazard - Substitution of components
may impair suitability for use in hazardous locations
TM
PELICAN CANADA
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel (780) 481-6076 • FAX (780) 481-9586
CAUTION:
If light is not to be used for some time, remove
batteries to prevent possible leakage and corrosion.
TM
WARNING! STATIC HAzARD - clean only with a
damp cloth
PELI PRODUCTS, S.L.U.
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
Advertencia - Peligro de explosión - Las baterías
sólo deben sustituirse o cargarse en zonas no peli-
grosas.
TM
StealthLite 2400
PELICAN LEGENDARY LIFETIME
GUARANTEE OF EXCELLENCE
Battery Replacement
Cat. #2400
Do not mix battery brands or use Nicad or zinc
Carbon Batteries. Do not mix old and new batteries.
Replace all batteries at the same time.
Pelican Products, Inc. guarantees its products for a
lifetime against breakage or defects in workmanship.
This guarantee does not cover the lamp or batteries
(rechargeable or alkaline). Any liability, either expressed
or implied, is limited to replacement of the product.
This guarantee is void if the Pelican product has been
abused beyond normal and sensible use.
INSTRUCCIONES DE FUNCIONAMIENTO
PRECAUCION:
INSTALACION DE LAS PILAS
Si no se va a usar la linterna por algún tiempo, retire
las pilas para evitar la posibilidad que ocurra una
fuga y corrosión.
Lamp Replacement
Lamp replacement may only be performed
in a non-hazardous area.
1. Retire el bastidor de la lente girándolo en
sentido contrario de las agujas del reloj.
2. Retire el módulo de la bombilla y el contacto.
3. Saque las pilas gastadas y sustitúyalas por pilas
nuevas tal y como se indica en la parte exterior del
cuerpo de la linterna.
4. Vuelva a colocar el módulo de la bombilla y el
contacto.
5. Vuelva a colocar el bastidor de la lente sobre la
rosca y gire en el sentido de las agujas del reloj al
mismo tiempo que ejerce un poco de presión sobre
el mismo.
This guarantee does not cover shark bite, bear attack or
damage caused by children under five.
REEMPLAZO DE LA BOMBILLA
1. Retire el bastidor de la lente girándolo en
sentido contrario de las agujas del reloj.
DO NOT MODIFY THIS PRODUCT!
Lifetime Guarantee does not cover Roto Molded or
for full details.
2. Retire el módulo de la bombilla y el contacto.
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to
Pelican Products Customer Service Department
(postage paid). Please call for a return authorization
number. Per our guarantee, Pelican Products will
replace or repair any broken or defective products.
Upon receipt of goods, Pelican Products will notify
you of any handling and return postage charges.
If your local retailer does not stock the above acces-
sory parts, you may order them directly from Pelican
Products. Send check or money order in U.S. dol-
lars, or order by phone using MasterCard or VISA
(ask for Customer Service). SORRY, NO C.O.D.’s.
Subject to sales tax. Allow 2-3 weeks delivery time.
Pelican Products pays postage and handling charg-
es. POSTAGE PAID FOR U.S. zIP CODES ONLY.
3. Vuelva a colocar el módulo de la bombilla y el
contacto.
4. Vuelva a colocar el bastidor de la lente sobre la
rosca y gire en el sentido de las agujas del reloj
al mismo tiempo que ejerce un poco de presión
sobre el mismo.
ENCENDIDO / APAGADO
Para encender la linterna (con el extremo de la bombilla
apuntando en la dirección opuesta a usted), gire la
palanca del interruptor hacia la derecha hasta que se
encienda. Para apagarla, gire la palanca del interrup-
tor hacia la izquierda (con el extremo de la bombilla
apuntando en la dirección opuesta a usted), hasta que
se apague.
ESPECIFICACIONES DEL PRODUCTO
Tipo de bombilla:
Xenón
Tipo de pila:
4 AA Cell Alkaline (Included)
Marca de las pilas: Energizer® de Eveready®
Advertencia - Peligro de explosión - La sustitución
de componentes puede afectar a la idoneidad de su
uso en zonas potencialmente explosivas.
PIEZAS DE REPUESTO
NO. DE CAT.
DESCRIPCION
2401
Junta tórica
2404
Módulo de la bombilla
|