Model
：PTC19LC
16:10 DIGITAL LCD-TV-Monitor
19 Hi-Definition LCDFlat Panel TV
OPERATING MANUAL
Contents
TROUBLESHOOTING
AND ADVICE
8
9
21
22
SPECIFICATIONS
2
PREFACE
Thank you for buying this TV ! Please read this manual thoroughly before operating the monitor.
Make sure the monitor was not damaged in transit. Should the monitor is damaged, do no install
it and contact your dealer. Check that you have all the accessories according to the model.
SAFETY PRECAUTIONS
Preparation
Put the monitor on a stable surface.
Do not use the monitor with others fixations than those provided or
suggested by the manufacturer.
Minimum distances
10cm
10cm 5cm
Do not place any material on the monitor.
20cm
Do not block or cover the ventilation openings on the monitor
If you have a wall mount, check that it is steady
Power source
The monitor must be plugged with a tension source of 110 volts and 60 Hz.
Connexion cables
Power cord and cables must be properly routed and protected to prevent
people from stepping on them and causing the monitor to fall.
3
Heating sources and humidity
Keep the monitor dry and away from humidity.
Keep the monitor away from heat sources
Cleaning and maintenance
Unplug the monitor before cleaning it. Do not use solvents or liquids
to clean the monitor.
Only clean the monitor with a soft and dry cloth.
In case of troubleshooting, do not use spare parts other than those
suggested by
the manufacturer. Using inadequate spare parts can lead to electric
shocks, short-circuits fire or other incidents.
Departure in holidays
Unplug the LCD during lighting storms or when unused for long periods
of time.
4
Front , Back , Connections of LCD
Front View
IR ON
/
OFF LED
Back View and Control Connections
RF IN
V IN
1
2
S VIDEO
HDMI
VGA
3
4
5
PC AUDIO
Pr
6
7
Pb
8
Y
9
R IN
10
11
12
13
L IN
PHONE
DC IN
VGA
S
VID EO
V
IN
RF IN
Pb
PC AUDIO
DC IN
PHONE
L
IN
R
IN
Y
Pr
HDMI
13
12 11 10
9
8
7
6
5
4
3
2
1
5
TV INSTALLTION DRAWINGS
CONNECTION ANTENNAS
VHF
ANTENNA
VHF
ANTENNA
OUTDOOR
ANTENNA
AMPLIFIER
INDOOR
ANTENNA
AMPLIFIER
75 OHM
ANTENNA
PLUG
POWER PLUG OF
ANTENNA
AMPLIFIER
To ensure good picture and sound, TV antenna system needs to be installed. The antenna system as
shown can be sourced from TV equipment shops, which will provide service for correct installation
and connection. After installation, insert the 75-ohm antenna plug into the antenna jack as shown.In
case of signal of closed circuit TV,
VIDEO CONNECTION
VGA
S
VID EO
V
IN
RF IN
DC IN
PHONE
L
IN
R
IN
Y
Pb
Pr PC AUDIO
HDMI
S VIDEO CONNECTION
VGA
S
VID EO
V
IN
RF IN
DC IN
PHONE
L
IN
R
IN
Y
Pb
Pr PC AUDIO
HDMI
6
PCINPUT CONNECTION
VGA
PC AUDIO
VGA
S
VIDEO
V
IN
RF IN
DC IN
PHONE
L
IN
R
IN
Y
Pb
Pr PC A UDIO
HDMI
7
Menu Operation
1. Connecting to the AC input cable then press the main power switch to switch ON LCD TV. At this time the TV will enter
standby mode and indicator show red.
2. Use POWER button can turn ON LCD TV from standby mode.
1. Press POWER button or
button on the remote control to enter standby mode. The indicator is red.
2. Using main power switch turns off LCD TV completely.
Tuning Band
Air
Picture
Audio
DTV-Signal
Auto Ch Search
Add On Ch Search
Manual Ch Set
Channel Labels
Menu Language
Setup
English
Feature
Enter
Menu
To Exit
To Move
To Select
Press MENU to display the main menu.
Press
Use
/
repeatedly to select the SET MENU.
and to select LANGUAGE.
and button to select your desired language.
/
/
P ress
When you are satisfied with your choice, press the MENU
to exit.
1. Press VOL+/- to adjust the volume.
2. If you want to switch the sound OFF , press the MUTE
.
3. You can cancel this function by pressing MUTE or VOL+.
8
Menu Operation
- Press the MENU button to display the main menu.
- Use
/
/
/
buttons to select and adjust the available menus.
Picture Mode
Contrast
Audio Mode
User
Voice
Picture
Audio
Picture
Audio
English
50
50
50
50
Audio Language
Brightness
Sharpness
Color
Bass
30
30
0
Treble
Balance
Tint
50
Digital Audio Output
PCM
Setup
Setup
Aspect Ratio
Wide
Feature
Feature
Menu
Menu
To Exit
Enter
Enter
To Move
To Select
To Exit
To Move
To Select
Time Set
Tuning Band
DTV-Signal
Air
Picture
Audio
Picture
Audio
Off
Sleep Timer
Advanced Video Menu
Password Set
Parental Control
Digital Closed Caption
Ntscc
Auto Ch Search
Add On Ch Search
Manual Ch Set
Channel Labels
Menu Language
Reset
Setup
Setup
CC
CC
English
Atscc
Feature
Feature
Menu
Enter
Enter
Menu
To Exit
To Move
To Select
To Exit
To Move
To Select
The OSD (On Screen Display) function enables you to adjust the screen status conveniently since it provides
graphical presentation.
Press CH+ to increase channel number.
Press CH - to decrease channel number.
You can select the channel number by pressing 0 to 9 or -/--.
To select 1-digit channel (e.g. Channel 5): Press the 5 button.
To select 2-digit channel (e.g. Channel 20): Press the -/-- button repeatedly to display -- then press 2, follow by 0.
To select 3-digit channel (e.g. Channel 103): Press the -/-- button repeatedly to display -- then press 1, follow by 0,
follow by 3.
You can select the input source by pressing the INPUT on the remote control or on the front panel.
9
Menu Operation
Ch
Video 1
Video 2
Video 3
Video 4
Video 5
In this manual, the OSD ( On Screen Display) may be different from your TV’ s because it is just example to help the
TV operation.
Picture Mode
Contrast
User
Picture
Audio
50
50
50
50
Brightness
Sharpness
Color
1. Use
/
to select what you want to adjust in the
Picture menu.
Tint
50
Setup
Aspect Ratio
Wide
2. Press
and
button to adjust.
3. When you are satisfied with your adjustment, press
Feature
Enter
Menu
To Exit
To Move
To Select
MENU to exit the main menu.
Select the type of picture which best corresponds to your viewing requirements by selecting Picture Mode in PICTURE
menu. You may select the picture mode directly by pressing the PMODE button on the remote control.
Press
Press
/
button and then use
button and then use
/
to adjust the contrast of the picture.
to adjust the brightness of the picture.
/
/
Press
/
button and then use
/
to adjust the sharpness level of picture.
Press
Press
/
/
button and then use
button and then use
/
/
to adjust the color saturation.
to adjust the tint of picture.
Press ◄/► to select the ratio of picture display such as Normal/ Zoom/ Wide and Cinema.
10
Menu Operation
Audio Mode
Voice
Picture
Audio
English
Audio Language
Bass
30
30
0
Treble
Balance
1. Use
/
to select what you want to adjust in the
Audio menu.
Digital Audio Output
PCM
Setup
2. Press
and
button to adjust.
3. When you are satisfied with your adjustment, press
Feature
MENU or EXIT to exit the main menu.
Enter
Menu
To Exit
To Move
To Select
You can select the type of sound which best corresponds to your listening requirements by selecting Sound in SOUND
menu. You may select the sound mode directly by pressing the SMODE button on the remote control.
Press ◄ / ►to select one of the audio language such as English/ French and Spain, but the condition is that the program
system has included the language code.
Press
Press
Press
/
/
/
button and then use
button and then use
button and then use
/
/
/
to increase or decrease the level of the lower-pitched sounds.
to increase or decrease the level of the higher-pitched sounds.
to adjust the audio output between left and right speakers.
Press ◄ / ► to select the one of mode of the digital audio output such as PCM and RAW.
Tuning Band
Air
Picture
Audio
DTV-Signal
Auto Ch Search
Add On Ch Search
Manual Ch Set
1. Use
/
to select what you want to adjust in the
Channel Labels
Menu Language
Reset
Setup menu.
Setup
English
2. Press
and
button to adjust.
3. When you are satisfied with your adjustment, press
Feature
Enter
Menu
To Exit
To Move
To Select
MENU to exit the main menu.
Press Enter key to select Air, Cable, Cable HRC, Cable IRC or Cable Auto.
In DTV mode, you can tune manually and adjust the angle, orientation of the antenna etc
11
Menu Operation
Press ▲ / ▼ key to move the cursor to the item to be selected (item selected is highlighted in yellow). Press Enter key to enter
your selection and scan. After the scan is finished, the following menu will display. The channels found are automatically
saved as below:
Autoprogram Menu
NTSC Channel 19
Not Found
2
0
Analog Channels Found
Digital Channels Found
Progress(%)
12
When the channels are found, use
/
to add it to the channel list.
Press Enter button to display a channel list that you can select channel as below:
Manual Channel Set Menu
Ch 42 -1
ATSCdmo
Viewable
Ch 2 -0
Viewable
Viewable
Viewable
Viewable
Viewable
Viewable
Viewable
Viewable
Ch 11 -0
Ch 22 -0
Ch 31 -0
Ch 52 -0
Ch 54 -0
Ch 66 -0
Ch 68 -0
Enter
M enu
To Exit
To Move
To Select
Allows you to name the channel that is selected. Use ◄ / ► to move the cursor and use ▲/▼ to input the name and then
press Menu or Enter to return or exit as following:
Channel Labels Menu
Ch 42-1
To Move
ATSC dmo
Enter
Me nu
To Change
To Exit
To select language of the OSD such as English/ French and Spain
12
Menu Operation
Time Set
Picture
Audio
Off
Sleep Timer
Advanced Video Menu
Password Set
1. Use
/
to select what you want to adjust in the
Parental Control
Digital Closed Caption
Feature menu.
Setup
2. Press
and
button to adjust.
3. When you are satisfied with your adjustment, press
Feature
MENU to exit the main menu.
Enter
Menu
To Exit
To Move
To Select
Press
/
button and then use Enter the time set menu as below that allows you to set the time the TV will display.
Time Set Menu
Time Set Mode
Auto
Time Zone
Year
Pacific
2006
Date
Dec 29
12:00 AM
Time
Enter
Me nu
To Exit
To Move
To Select
You can select one of auto and manual to set the time.
When selected auto, the item of year/date and time will be
disabled and can not to adjust. When select the manual
mode, you can press ◄/► and ▲/▼ to set the corresponding
functions.
Press ◄/► to select the time zone such as Pacific/ Alaska/
Hawaii/ Eastern/ Central/Mountain.
Press ◄/► to select the amount of time before your TV turn off automatically and press the Enter that can select the 30 min
/60min/90min and OFF.
Press Enter to enter the advance video menu as below:
Advance Video Menu
Noise Reduction--Spatial
Off
Noise Reduction-- Speckle
Noise Reduction-- Temporal
Color Temperature
3D Y/C
Off
Off
Normal
On
Adaptive Contrast
Setting
On
Preset
Ent er
M enu
To Exit
To Move
To Select
13
Menu Operation
- Noise Reduction--Spatial: press Enter to select on or off.
- Noise Reduction--Speckle: press Enter to select on or off.
- Noise Reduction--Temporal: press Enter to select on or off.
- Auto Contrast Enhancement: press Enter to select on or off.
- Color Temperature: press Enter to select one of Normal/Cool
and Warm.
- 3D Y/C: press Enter to select on or off.
- Adaptive Contrast: press Enter to select on or off.
- Setting: press Enter to return to the factory setting.
Press Enter to enter the Enter Old Password menu, and then input the number of 0-9 as below, and you can change the
password when you input the new one twice.
Enter Old Password
Press Enter to enter the sub-menu and then uses the 0-9 to enter the correct password.
Candlan Rating Menu
Candlan English
Candlan French
E
C
E
G
C8+
G
8 ans+
13 ans+
16 ans+
18 ans+
PG
14+
18+
Enter
Menu
To Exit
To Move
To Select
This item allows you to set the closed caption, and press Enter to enter Closed Caption Options menu as below:
Digital Closed Caption
Style
Automatic
Automatic
Automatic
Size
Font
Text Color
Automatic
Automatic
Automatic
Text Opacity
Background Color
Background Opacity
Edge Effect
Automatic
Automatic
Automatic
Edge Color
DECIDED BY BROADCASTING
Ent er
M enu
To Exit
To Move
To Select
14
Menu Operation
- Style: press Enter to select one of Automatic and Custom, when you select automatic, the others are disable and can not be
adjusted.
- Size: press Enter to select one of Normal/Large and Small.
- Font: press Enter to select one of Default and from Font1 to Font7.
- Text Color: press Enter to select one of Red/Green/Blue/Yellow/Magenta/Cyan/Black and White.
- Text Opacity: press Enter to select one of the Solid/Flashing/Transparent/Translucent.
- Background Color: press Enter to select one of the Black/White/Red/Green/Blue/Yellow/Magenta/Cyan.
- Background Opacity: press Enter to select one of the Solid/Flashing/Transparent/Translucent.
- Edge Effect press Enter to select one of the None/Raised/Depressed/Uniform/Left Shadow/Right Shadow.
- Edge Color press Enter to select one of the Black/White/Red/Green/Blue/Yellow/Magenta/Cyan.
Time Set
Picture
Sleep Timer
Off
Advanced Video Menu
VGA Set
Audio
1. Use
/
to select what you want to adjust in the
Feature menu.
Setup
2. Press
and
button to adjust.
Feature
3. When you are satisfied with your adjustment, press
Enter
Menu
To Exit
To Move
To Select
MENU to exit the main menu.
Press
/
button and then use Enter to enter the VGA set menu as below:
VGA Setting-1024x768@70Hz
H-Pos
50
50
V-Pos
50
50
Clock
Phase
Auto Adjust
Preset
Setting
Enter
Menu
To Move
To Select
To Exit
Press
Press
Press
/
button and then use
button and then use
button and then use
/
/
adjust the horizontal position of the picture.
adjust the vertical position of the picture.
to adjust the phase of the picture.
/
/
/
Press
/
button and then use
/
to adjust the clock of the picture.
15
Menu Operation
-Phase
-Clock
This function allows you to remove any horizontal
noise and clear or sharpen the image of characters
This function is to minimize any vertical bars or stripes
visible on the screen background. And the horizontal
screen size also will change.
-Position This function is to adjust the picture to Left/Right
and Up/Down as you prefer..
Press
/
button and then use
/
to do auto adjust that automatically adjusts the available options for the best viewing
configuration.
Press Enter to do preset that can return to the factory setting.
Time Set
Picture
Off
Sleep Timer
Advanced Video Menu
Component Set
Audio
1. Use
/
to select what you want to adjust in the
Feature menu.
Setup
2. Press
and
button to adjust.
3. When you are satisfied with your adjustment, press
Feature
MENU to exit the main menu.
Enter
M enu
To Exit
To Move
To Select
Press
/
button and then use Enter to enter the VGA set menu as below:
Component Setting-720x480I@30/29.97Hz
H-Pos
50
50
50
50
V-Pos
Clock
Phase
Auto Adjust
Preset
Setting
Enter
M enu
To Exit
To Move
To Select
16
Menu Operation
Time Set
Picture
Audio
Sleep Timer
Off
Advanced Video Menu
Setup
Feature
Enter
Menu
To Exit
To Move
To Select
Press
/
button and then use Enter the time set menu as below that allows you to set the time the TV will display.
Press ◄/► to select the amount of time before your TV turn off automatically and press the Enter that can select the 30 min
/60min/90min and OFF.
Press Enter to enter the advance video menu.
Advanced Video Menu
On
Noise Reduction --Spatial
On
Noise Reduction --Speckle
On
Noise Reduction --Temporal
Color Temperature
Normal
3D Y/C
On
Menu
To Exit
To Move
To Change
17
REMOTE CONTROL
Remote control instructions
Switch on LCD TV when at standby mode or vice
versa.
Press to mute the sound. Press again or press
VOL+ to unmute.
PMODE SMODE
Press 0-9 to select a TV channel directly when you
are watching TV. The channel change after 2 seco-
nds.
VOL
CH
-/--
Press this button to enter a program number for
multiple program channel such as 2-1,etc.
MENU
EXIT
SOURCE CCD
ZOOM
MTS
SLEEP
EPG
Return to the previous channel viewed.
Press to scan through channels. To scan quickly
channels, press and hold down either +/-button.
FAV
FAV
FAV
Press to increase / decrease the sound level.
Press repeatedly to cycle through the available video
picture modes.
Press to cycle through the different sound settings.
Press to display the source and channel’s info-
rmation.
18
Allows you to navigate the on-screen menus and
adjust the system settings to your preference.
Clears all on-screen displays and returns to TV
viewing from any menu.
PMODE SMODE
Brings up the main menu to the screen.
VOL
CH
MENU
EXIT
Press to cycle through the input source in following:
Ch
Video1
Video3
Video4
Video2
Video5
SOURCE CCD
ZOOM
MTS
SLEEP
EPG
Closed caption button.
Audio selection button.
FAV
FAV
FAV
Lets you select amount of time before your TV turn
itself off automatically..
Enlarges the main picture size.
Press to enter the EPG menu directly.
Press to enter the favorite menu.
Press to increase the program which you favorite.
Press to descrease the program which you favorite.
19
Battery Usage Caution
a)Open the cover
b)AA size batteries, When inserting the batteries, make sure correct polarities as per”+“and ”-“marks
on the batteries and within the battery compartment
c)Replace the battery cover
To prevent battery leakage which may result in bodily injury or damage to the remote:
1.Install all batteries correctly, and as marked on the remote control.
2.Do not mix batteries:(OLD and NEW or CARBON and ALKALINE, etc)
Remove batteries when the remote is not used for a long time.
ACCESSORIES
1 Adapter Plug
2 One Remote Control
3 2 Batteries 1.5V
4 One User Manual
20
TROUBLESHOOTING AND ADVICE
Before calling our SAS centre, please check if you can solve the troubleshooting by yourself.
Troubleshooting
No signal
Control
Please check that all cables and cord's are correctly plugged in.
Adjust the contrast, the color and the brightness
No color shades
May be result from a lighting signal from car, motor, neon light and
other electrical devices or appliances.
Stain show on the
screen.
Double or multiple
display image
May be the result of an electrical wave disturb from other TV,
Computer and Game machine or Radio
The cables of the antenna are not correctly plugged in.
Snow on the screen
The remote control
does not work
Please check the batteries order and alignment.Check that the IR
of the remote control is not hidden by something.
Even if the display image is correct, the noise may come from an
unsteady fixation of the panel.
"Zip" made noise on
TV cover
Make sure that you have not press the MUTE button of the panel
or of the remote control.
No sound
21
SPECIFICATIONS
19 Inch
TFT LCD
1440* 900
400cd/㎡
16.2M
Screen Size
Display Type
Resolution(Pixel)
Brightness
Color
500 : 1
Contrast Ratio
View Angle(H/V)
Aspect Ratio
160 /135
16:10
AC IN PUT
TV System
110V/220 Voltage Selectable
NTSC
Video Input Format
Antenna Input
Audio Output
NTSC
Standard antenna socket 75Ω
L / R 10W*2
Video 1.0vp-p75Ω;RCA
Y:1.0Vp-p±3db C:0.3Vp-p±3db
Video
S-Video
Input
640*480/60Hz 、 800*600/60Hz 、 1024*768/60Hz
PC
Audio
(Videos-Video-PC)
R/L200mVrms (max3.0vp-p)20ΩkRCA
Weight
11 lbs
Dimensions (with stand)
19.5 W x 16.8 H x 2.8 D
This manual is only for your reference, any change to the design and specification will not
be advised.
22
|